polishing heels

WRCOLLINS

Member
Joined
Jun 5, 2019
Messages
14
Trying my darnedest to get my gravers sharp for western bright cut. Using a powerhone up to 1200gt. I think I am not understanding how polished the heels need to be and I have seen that some suggest "rolling" the heel. Trying a 45d face and 15d heel. Examining them under a loop...they look sharp, but don't seem to glide as I work.....any help from anyone would be appreciated.
Also have purchased disposable disc in 3000/5000/10000 grit.
Also after polishing the heel to a mirror finish, the graver seems dull.

Just a novice here, so be gentle!
 

WRCOLLINS

Member
Joined
Jun 5, 2019
Messages
14
I have her dvds and have not gotten to disc 2...ill check it out...thanks.
 

Sinterklaas

Elite Cafe Member
Joined
Dec 19, 2015
Messages
198
Location
Holland
If your graver is sharp after 1200. But after using the wheels it is dull. Then you are using the wheels wrong. I got the same problem when I started using the diamond polishing wheels from GRS. You need to adjust the way you hold the graver on the wheels. Try to lean a little bit away from the surfaces you want to stay sharp. Also the wheels might not be perfectly flat themselves to begin with. You can flatten them with a coarse diamondwheel.
 

WRCOLLINS

Member
Joined
Jun 5, 2019
Messages
14
Thank you...adding all these comments together and going to go back to the wheels.
If your graver is sharp after 1200. But after using the wheels it is dull. Then you are using the wheels wrong. I got the same problem when I started using the diamond polishing wheels from GRS. You need to adjust the way you hold the graver on the wheels. Try to lean a little bit away from the surfaces you want to stay sharp. Also the wheels might not be perfectly flat themselves to begin with. You can flatten them with a coarse diamondwheel.
 

lucylu

New Member
Joined
Jul 9, 2012
Messages
1
I’m just wondering if you find there are any times when your tool glides? I find copper and particularly silver rather ‘sticky’ metals to cut into, so I don’t find they are best for ‘gliding’. Just a thought. Another thought is that your tool is very likely to be sharp, so perhaps any variations in cutting feel is more to do with where you hold your arm as you are working? Sorry if that’s not helpful though x
 

Archie Woodworth

Elite Cafe Member
Joined
Dec 10, 2010
Messages
293
Location
Northeastern North Carolina
Use a cast iron lap and diamond dust...quick and easy way to polish the heal....and face if you want a mirror finish. If you only polish the heal you still will have a "sawtooth" cutting...tho it probably, it doesn't matter (I'm guessing) all that much as the heal is probably "smoothing out" any irregularities in surface as it moves along.
 

mitch

~ Elite 1000 Member ~
Joined
Jul 23, 2007
Messages
2,635
"and face if you want a mirror finish. If you only polish the heel you still will have a "sawtooth" cutting"

AND you have to polish the rear/trailing edge of the heel facet(s) where they meet the bottom/belly of the graver body. rather than polish a tiny flat length of the belly, i recommend slightly rounding off that 'corner' by holding the belly of the graver flat against the polishing surface (i use a fine ruby stone), then lifting the graver as you draw it back on the stone. if you're using a powerhone, do this delicate operation with it turned off. you may want to strop it with some ultra-fine diamond compound on hard maple or MDF.

otherwise, you'll get the same drag marks from the rear of the heel as you would with an unpolished face.
 
Last edited:

papart1

:::Pledge Member:::
::::Pledge Member::::
Joined
May 23, 2015
Messages
1,308
Location
Michigan
Mitch..........I think you solved my heal drag problem also especially with narrow inlay channels. Thank you sir.
 

Sponsors

Top