Question: Tricks for flare cutting?

rweigel

Elite Cafe Member
Joined
Dec 22, 2017
Messages
203
Location
France (north of Alsace, close to Germany)
Would it be OK to wet the graver with some oil for flare cutting? My high speed steel gravers cut considerably faster with oil.

Using a turntable, do you normally grab the vise or the turntable when turning it?

Best regards,

Ralf
 

Roger Bleile

~ Elite 1000 Member ~
Joined
Oct 4, 2007
Messages
2,988
Location
Northern Kentucky
I do the same as Sam. An important aspect is to make your cuts in one continuous pass. Any stopping then starting in a cut will show progression marks that detract from the look. While watching a skilled engraver on video like Sam or Chris DeCamillis looks easy, flare cutting requires excellent graver control.
 

Roger Bleile

~ Elite 1000 Member ~
Joined
Oct 4, 2007
Messages
2,988
Location
Northern Kentucky

rweigel

Elite Cafe Member
Joined
Dec 22, 2017
Messages
203
Location
France (north of Alsace, close to Germany)
Dear Roger,

thanks a lot for your advice and the link to your tutorial. I‘ll go through it toroughly. I got Sam‘s instruction video quite early and work my way trough it since weeks.

I‘m always amazed how much detailed information is provided by you „great names“ in engraving to newbies like me and with how much patience my questions are answered. I can’t thank all the contibutors enough for it. I‘m an electronics engineer with a goldsmith workshop in my basement. My main purpose is jewelry making. I pick up practical skills from craftsmen who were willing to share them, in Germany, Turkey and Tunisia so far. Up until two years ago, I used graver mostly for stone setting and cleaning up after soldering.

Best regards,

Ralf
 

monk

Moderator
Staff member
::::Pledge Member::::
Joined
Feb 11, 2007
Messages
10,857
Location
washington, pa
sinc joining the forum, i've seen a whole raft of buckles. many, if not most, were very complex, ornate, and quite beautiful. to this day, the buckle roger did is still my very favorite. it's not complex,rather somewhat un complicated. none the less, it is a mesmerizing piece to look at. when you see it, i think you might agree.
 
Last edited:

Sam

Chief Administrator & Benevolent Dictator
Staff member
Joined
Nov 6, 2006
Messages
10,490
Location
Covington, Louisiana
I'm pretty sure I mention in the video that the more metal you remove per cut, the greater the demands of graver control. Flare cutting is prefect example of that, as is script lettering. But flare cutting probably requires a bit more because it's often a much larger, longer, and wider cut than script.

I can promise you this...all of your engraving will benefit from the skills developed learning flare cutting.
 

monk

Moderator
Staff member
::::Pledge Member::::
Joined
Feb 11, 2007
Messages
10,857
Location
washington, pa
well. i've given the flare cut a try. uh, it aint as easy as it looks. it's like i'm learning all over again. what have i always told people ? yeah, i must practice.
 

Chujybear

~ Elite 1000 Member ~
Joined
Nov 3, 2011
Messages
1,079
Location
Haida Gwaii
Would it be OK to wet the graver with some oil for flare cutting? My high speed steel gravers cut considerably faster with oil.

Using a turntable, do you normally grab the vise or the turntable when turning it?

Best regards,

Ralf


Your first question.. it would not impede you to have oilm on your tool.. so it is okay
 

cropduster

Elite Cafe Member
Joined
Feb 5, 2013
Messages
131
Location
Southwest Pennsylvania

monk

Moderator
Staff member
::::Pledge Member::::
Joined
Feb 11, 2007
Messages
10,857
Location
washington, pa
chris: do you happen to have a dwg of the tool you used in the video. i started to cut the way you do, both directions. i'd think your graver would be better for cutting both directions.
 
Last edited:

speeedy6

Elite Cafe Member
Joined
Sep 16, 2013
Messages
271
Is the flare cut style only suitable for bright cutting? I mean how would it look blackened or on a blued gun ? And, is it acceptable to mix one style with another style like American Scroll with some Flare cutting in some odd or remote areas ? Thanks, Mark
 

Sam

Chief Administrator & Benevolent Dictator
Staff member
Joined
Nov 6, 2006
Messages
10,490
Location
Covington, Louisiana
Is the flare cut style only suitable for bright cutting? I mean how would it look blackened or on a blued gun ? And, is it acceptable to mix one style with another style like American Scroll with some Flare cutting in some odd or remote areas ? Thanks, Mark

IMO it doesn't look good blackened. It struts its stuff when it's really bright and sparkly. On a blued gun I think it'd be quite nice, and it can be mixed with other styles if done correctly. There's no simple answer for that...you have to approach mixing styles very carefully
 

monk

Moderator
Staff member
::::Pledge Member::::
Joined
Feb 11, 2007
Messages
10,857
Location
washington, pa
mixing styles for me, is ok. that is if the overall effect harmonizes well in the area it is applied. personally, i never did much of this.
 

speeedy6

Elite Cafe Member
Joined
Sep 16, 2013
Messages
271
Sounds like mixing styles is ok , if, you know what you're doing, I better stay away from that for a while. Thanks for the replies, Mark
 

Ed Westerly

~ Elite 1000 Member ~
Joined
Mar 16, 2011
Messages
1,224
Location
southern California
I have engraved guns where I used traditional methods on part of the gun and flared cutting on other areas, and they turned out the way I wanted them to. You need a large gun like a Winchester 92 or 73 so the styles can be separated and have their own integrity, so for example, I wouldn't mix styles on most handguns.
 

Mike Cirelli

~ Elite 1000 Member ~
Joined
Nov 8, 2006
Messages
1,690
Location
Western PA
Flare cutting is a lot of fun. The discipline that Sam uses cutting the backbones is amazing. In his video he makes it look easy but it's not. His video makes you want to strive for that perfection though.
 

Monica

Member
Joined
Feb 14, 2017
Messages
59
Location
Los Angeles, CA
Dear Roger,

thanks a lot for your advice and the link to your tutorial. I‘ll go through it toroughly. I got Sam‘s instruction video quite early and work my way trough it since weeks.

I‘m always amazed how much detailed information is provided by you „great names“ in engraving to newbies like me and with how much patience my questions are answered. I can’t thank all the contibutors enough for it. I‘m an electronics engineer with a goldsmith workshop in my basement. My main purpose is jewelry making. I pick up practical skills from craftsmen who were willing to share them, in Germany, Turkey and Tunisia so far. Up until two years ago, I used graver mostly for stone setting and cleaning up after soldering.

Best regards,

Ralf
I'm still a newbie and agree that no lubrication is needed for flare cutting. You can get the cuts that you need by rotating your vise. Lots of practice is needed....lots.
 

Latest posts

Sponsors

Top