New Favorite Fixture

[Beathard]

I don't often sing the praises of a fixture or review them for that matter. But I just received a new one that I have to tell you about.

It is a fixture designed to hold a 1911 slide. I've done 18 1911s since FEGA a month ago. The last few were with this fixture.

I have had no scratches caused by metal chips vibrating between the slide and the vise. I've had no scratches due to the slide slipping in the vise when doing deep relief or dot punch. I've had no slides changing their slide to frame fit due to over tightening the vise. For these reasons and several others I love this fixture.

If you are interested they are made by Sandy. If you dont know how to get hold of him PM me.

 

[monk]

very nice. after tearing my hair out trying different holds for the slides, i setteled on a common hardwood block. there was no vise contact, as i fitted the slide to the wood, then used a bit of hot melt. worked for me, but yours is far, far, better looking. for guys & gals that like store-bought, this looks like a winner.

 

[Beathard]

Yeah Monk, I tried that too. But when you want to maximize time cutting and not engineering ways to hold stuff, this is the answering figure it will pay for itself in two weeks.

 

[Ragnarok]

as a builder of 1911's, this is the fixture i use for holding slides for milling.http://www.brownells.com/gunsmith-tools-supplies/handgun-tools/slide-tools/yavapai-1911-slide-jig-prod929.aspx it might work for engraving too.

 

[Sandy]

Ragnarok,
I made my first one about 40 years ago for milling the 1911 slide for sights. About 10 years ago I adapted it for engraving slides. I made one for My friend Dale Bass and he came up with the idea of the angle plate on the side. Works great.
Sandy

 

[Ragnarok]

Ragnarok,
I made my first one about 40 years ago for milling the 1911 slide for sights. About 10 years ago I adapted it for engraving slides. I made one for My friend Dale Bass and he came up with the idea of the angle plate on the side. Works great.
Sandy

yeah, I really like your jig. it's not nearly as obtrusive as the one I linked to. I will probably "borrow" your idea soon.

 

[speeedy6]

I just can't get over " 18 1911's in a month" ! DANG !

 

[Sandy]

Ragnarok,
If you do build one I use 3/4" X 2" 6061-T6511 aluminum (less chance of messing up engraved slide with aluminum). Murphy's law is alive and well. If you have any questions send me a pm.
Sandy

 

[Ragnarok]

Ragnarok,
If you do build one I use 3/4" X 2" 6061-T6511 aluminum (less chance of messing up engraved slide with aluminum). Murphy's law is alive and well. If you have any questions send me a pm.
Sandy

I'll probably use a block of nylon for the actual slide block, and aluminum angle on the side.

 

[Sandy]

Nylon cool idea for engraving fixture. I'll have to look into that. I us my fixture for mill and other activities. Would the nylon flex under milling forces?

 

[sam]

What a nice fixture.

Back in the day before vises were invented we just held held 'em between our knees. You had to be tough to be an engraver back then.

 

[Brian Marshall]

Yeah, and there were all those snowdrifts to walk through to get to the shop. All uphill too...


Brian

 

[Choppers_rule]

So I'm not suppose to just clamp the slide in the vise with piece of leather? Isn't a slide should be strong enough to withstand clamping force from the vise?

 

[Sandy]

Yes you can clamp it in the vise. But you should be careful to not squeeze the sides of the slide to much. That will create a whole new proble.

Here in Kansas we have to worry about the wind blowing us off the stool while engraving or other things. LOL

 

[Brian Marshall]

Simplest solution...

Brian

 

[Choppers_rule]

Thank you Sandy! That's a really good idea inserting an aluminum strip in the slide to prevent damage from clamping and more affordable for a newbie like me.

 

[Sandy]

That is a piece of oil hardened tool steel 3/4" wide by 3/32" thick. some things are better in steel.

 

[Choppers_rule]

That is a piece of oil hardened tool steel 3/4" wide by 3/32" thick. some things are better in steel.

Oh ok, I thought by using a softer metal would decrease the tendency of scratching the slide.

 

[Omar Haltam]

Very nice write up Beathard, thanks for the great tip....
And great looking Vice Sandy, maybe in the future when I start engraving 1911 slides I can order one from You

 

[Sandy]

When you are ready Omar let me know.

Choppers Rule
That is true. But aluminum that thin can flex and if you squeeze the slide to much you take the chance of cracking the slide or squeezing the sides of the slide in and it won't go back on the frame.
A couple of headaches you don't want. Been there and done that in years past. That's what brought the original fixture about back when I was building 1911s.