Show us your favourite chasing hammer

Mike Dubber

Elite Cafe Member
Joined
Nov 10, 2006
Messages
424
Location
Evansville, IN
These are my favorites - one at Bench #1 and the other at Bench #2. #3 is in my travel/teaching case. They are used daily - couldn't work without them.

They were made by A.G. Duncan who lived in California - he had an ad in the early Engraver Magazines and they were named the "1800's Chasing Hammer." Mr. Duncan is deceased so they are no longer available.

Notice that the heads have a heavy and light face. That helps balance the "strike." Notice also that the handle sections are very slim...about 1/4" wide near the center, allowing the hammer to rebound after the strike (deadfall hammers are no good for chasing). I have also added registration pins (a 3/32" steel rod) into the palm. Those are used to register the hammer in my hand without having to look at it when I pick it up. I can pick up the hammer, register the pin between the second and third finger, and I know the hammer is properly aligned in my hand for the strike, i.e., the heavy face is down. It's an auto-response, and it happens without thinking every time I pick up a hammer.

Having engraved for about 15 years before the advent of airpower I think it is valuable to provide basic hammer technique in all my classes. The chasing hammer technique I use and teach is described in detail in James B. Meeks book "The Art of Engraving."

I also like Sam Alfano's chasing hammer, although I have thinned the handle section for a more lively rebound.
Hammers.jpg
 
Last edited:

JJ Roberts

:::Pledge Member:::
::::Pledge Member::::
Joined
Nov 10, 2006
Messages
3,457
Location
Manassas, VA
These are my favorites - one at Bench #1 and the other at Bench #2. #3 is in my travel/teaching case. They are used daily - couldn't work without them.

They were made by A.G. Duncan who lived in California - he had an ad in the early Engraver Magazines and they were named the "1800's Chasing Hammer." Mr. Duncan is deceased so they are no longer available.

Notice that the heads have a heavy and light face. That helps balance the "strike." Notice also that the handle sections are very slim...about 1/4" wide near the center, allowing the hammer to rebound after the strike (deadfall hammers are no good for chasing). I have also added registration pins (a 3/32" steel rod) into the palm. Those are used to register the hammer in my hand without having to look at it when I pick it up. I can pick up the hammer, register the pin between the second and third finger, and I know the hammer is properly aligned in my hand for the strike, i.e., the heavy face is down. It's an auto-response, and it happens without thinking every time I pick up a hammer.

Having engraved for about 15 years before the advent of airpower I think it is valuable to provide basic hammer technique in all my classes. The chasing hammer technique I use and teach is described in detail in James B. Meeks book "The Art of Engraving."

I also like Sam Alfano's chasing hammer, although I have thinned the handle section for a more lively rebound.
View attachment 47919
Here's a few chasing hammers that I've collected over the years.
 

Attachments

  • 185980358_459945135262778_76734593190020514_n.jpg
    185980358_459945135262778_76734593190020514_n.jpg
    157 KB · Views: 39

Mike Dubber

Elite Cafe Member
Joined
Nov 10, 2006
Messages
424
Location
Evansville, IN
Yes, they are Louis Daniels Nimschke's - sorry to say they are not mine.
Here is the larger collection of Nimschke tools. These photos are from an auction conducted several years ago.
I found the photos while doing an LDN search - the auction was held in the early 2000's, and the price of the sale was not given.
 

Attachments

  • LDN_05.jpg
    LDN_05.jpg
    79.9 KB · Views: 39

Sam

Chief Administrator & Benevolent Dictator
Staff member
Joined
Nov 6, 2006
Messages
10,490
Location
Covington, Louisiana
Here are mine but it's hard to pick a fav.
 

Attachments

  • chasing hammers.jpg
    chasing hammers.jpg
    120.6 KB · Views: 50

Roger Bleile

~ Elite 1000 Member ~
Joined
Oct 4, 2007
Messages
2,988
Location
Northern Kentucky
Yes, they are Louis Daniels Nimschke's - sorry to say they are not mine.
Here is the larger collection of Nimschke tools. These photos are from an auction conducted several years ago.
I found the photos while doing an LDN search - the auction was held in the early 2000's, and the price of the sale was not given.
They were purchased by the late Bob Lee who donated them to the Metropolitan Museum of Art in NYC.
 

Roger Bleile

~ Elite 1000 Member ~
Joined
Oct 4, 2007
Messages
2,988
Location
Northern Kentucky
My favorite looks quite ordinary (I don't have a picture). It was given to me by Jean Francois DuBois who was an instructor at the Leon Mignon school in Liege, Belgium. I met him at the IWA show in Nuremberg, Germany. After a brief conversation he just gave it to me which means a lot to me. You can see Jean working with it in the picture below. The two in the other picture, I made about 40 years ago. The upper one has a bronze head and is very light.
 

Attachments

  • Jean Francois Dubois 2.jpg
    Jean Francois Dubois 2.jpg
    86.4 KB · Views: 41
  • Chasing Hammers.JPG
    Chasing Hammers.JPG
    70.5 KB · Views: 42

mitch

~ Elite 1000 Member ~
Joined
Jul 23, 2007
Messages
2,635
i must be the only engraver on the planet with just one chasing hammer, but it is a Friedrich Dick with the coveted, long out of production, 7/8" face. i made the replacement handle and would not recommend using beech for that. it's been re-wedged about six times...
 

Attachments

  • IMG_1219.jpeg
    IMG_1219.jpeg
    132.3 KB · Views: 30
  • IMG_1223.jpeg
    IMG_1223.jpeg
    66.4 KB · Views: 30
  • Like
Reactions: Sam

Mike Dubber

Elite Cafe Member
Joined
Nov 10, 2006
Messages
424
Location
Evansville, IN
I like the shape of the handle and the palm swell Mitch- I could chase gravers with that one!

Several years ago I knocked one of my 1880's hammers off the bench. When I pushed my chair back to retrieve it I rolled over the handle - you know, one of those with the finely crafted, thin, and flexible shafts I talked about.
I spent hours making a new one out of hickory...still using it today.
 

Chujybear

~ Elite 1000 Member ~
Joined
Nov 3, 2011
Messages
1,079
Location
Haida Gwaii
My favorite right now. Plus the only one I can find (in middle of a move)
 

Attachments

  • 53C5230B-1C03-4505-9EBF-3F4219A27B12.jpeg
    53C5230B-1C03-4505-9EBF-3F4219A27B12.jpeg
    122.3 KB · Views: 29
  • 0CBC16B4-D21B-48B6-88A0-6C8C70EF2B63.jpeg
    0CBC16B4-D21B-48B6-88A0-6C8C70EF2B63.jpeg
    123.2 KB · Views: 30
  • 5EE73404-A8A8-4557-A2B0-B5DC6E89902B.jpeg
    5EE73404-A8A8-4557-A2B0-B5DC6E89902B.jpeg
    123.2 KB · Views: 29

AllenClapp

Elite Cafe Member
Joined
Aug 7, 2019
Messages
377
Location
Raleigh, NC
i must be the only engraver on the planet with just one chasing hammer, but it is a Friedrich Dick with the coveted, long out of production, 7/8" face. i made the replacement handle and would not recommend using beech for that. it's been re-wedged about six times...
You might want to try pecan. We used to make bows out of pecan.
 
Top