Getting started 2

JKirby

Member
Joined
Jan 26, 2019
Messages
10
So,. Following advice from this forum I went with the best I could afford. Jumped in with both feet and bought a Gravermach AT, Magnum ATSS and QC901 ATSS handpieces. Magnablock, and now have a complete power hone system. Plus a bunch more smaller tools to make life easier (I have saved four years for this day).
Last night I was assembling the hand pieces and found a shortage of information on all the pieces. I have a bunch of small screws left over!
Anyone know what they're for?
 
Last edited:

Sinterklaas

Elite Cafe Member
Joined
Dec 19, 2015
Messages
198
Location
Holland
If there are multiple end caps for the airtact then maybe they belong to those. Or they are just extra in case you loose some.
 

monk

Moderator
Staff member
::::Pledge Member::::
Joined
Feb 11, 2007
Messages
10,857
Location
washington, pa
now that you have all the toys, better set them aside for a day or two.; get yerself a good pencil. you will need it. learning to draw is as important as an arsenal of tools. good luck to you in your endeavor.
 

JKirby

Member
Joined
Jan 26, 2019
Messages
10
now that you have all the toys, better set them aside for a day or two.; get yerself a good pencil. you will need it. learning to draw is as important as an arsenal of tools. good luck to you in your endeavor.
Yes sir. I've been using an Ngraver II for awhile now (all I could afford). Still have it set up and practicing with it... A good dependable tool. Been practicing drawing scrolls. Where I'm lacking is computer skills. Just found this forum a month ago.
 

monk

Moderator
Staff member
::::Pledge Member::::
Joined
Feb 11, 2007
Messages
10,857
Location
washington, pa
Yes sir. I've been using an Ngraver II for awhile now (all I could afford). Still have it set up and practicing with it... A good dependable tool. Been practicing drawing scrolls. Where I'm lacking is computer skills. Just found this forum a month ago.
no doubt the computer saves a lot of time. but, there are times when transfers (at least for me) are too time consuming.
i began drawing oversized, and then scanning the main part of the design. resizing in corel, then making a transfer.
 

JKirby

Member
Joined
Jan 26, 2019
Messages
10
no doubt the computer saves a lot of time. but, there are times when transfers (at least for me) are too time consuming.
i began drawing oversized, and then scanning the main part of the design. resizing in corel, then making a transfer.
Congratulations on your new gear!
Sam... Thank you Sir!
no doubt the computer saves a lot of time. but, there are times when transfers (at least for me) are too time consuming.
i began drawing oversized, and then scanning the main part of the design. resizing in corel, then making a transfer.
Monk... Thank you! This helps more than you know! Now I've discovered Coreldraw! I've got to figure out how to transfer... Right now I'm having to much fun with the new gear! Lol
 

monk

Moderator
Staff member
::::Pledge Member::::
Joined
Feb 11, 2007
Messages
10,857
Location
washington, pa
Sam... Thank you Sir!

Monk... Thank you! This helps more than you know! Now I've discovered Coreldraw! I've got to figure out how to transfer... Right now I'm having to much fun with the new gear! Lol
well, my thought is-- if i scan a drawing that i created, it's not "cheating" i simply think i'm working with my own creativity, aided and abetted by the computer. jmho
 

JKirby

Member
Joined
Jan 26, 2019
Messages
10
well, my thought is-- if i scan a drawing that i created, it's not "cheating" i simply think i'm working with my own creativity, aided and abetted by the computer. jmho
Right... It is your creation. I looked into Corel and do not have a system to support it yet. Maybe someday. I've got Diane Scalese's video on western bright cut engraving and at this time I'm just following her direction. My artistic ability is limited to scrolls and I'm hoping to expand from there. I see some of the work/art being created on this forum and am in genuine awe and deeply appreciative of the sharing/instruction. Thank you everyone.
 

JKirby

Member
Joined
Jan 26, 2019
Messages
10
her video, at least the one i saw, was top shelf !
The set is two discs containing 4-1/2 hours of pure information! She explains in detail each cut and why things are done a certain way. I couldn't be more happier. Next video will be on lettering and monograms. First I need to get some opinions on which videos cover these topics. Of course it's going to take me awhile to glean all the information off of her videos. Watched them twice now and still learning.
 

Sponsors

Top