Search results

  1. Adder

    Another Knife

    Thank you all for nice comments. Really appreciate it ! :graver: :):thumbsup::thumbsup:
  2. Adder

    Another Knife

    Hi again forum friends Not so much engraving lately, but have made a knife to my sisters daughter with theme from our national costume in northern Norway (Nordlandsbunad). The engraving isn`t the most adwanced, but it turned out okey I think. Here is some pictures during process and som picture...
  3. Adder

    special adaptor

    I have never tried soldering theese tubes, only superglue, and it works for me Monk.
  4. Adder

    Rodeo knife for Blade Show Texas

    Fabulous Brian!! :graver::tiphat:
  5. Adder

    Critique Request Drawing for practice plate

    Much better now. Else as John B says, and more lines as AllenClapp mention earlier. You getting there. Keep cutting! Jørn-Ove
  6. Adder

    Office desktop plaque

    Thanks for the info Evgeni:-)
  7. Adder

    Office desktop plaque

    Really nice Evgeni.:thumbsup: Did you also use the GRS-handpiece for the walnut inscription too? Jørn-Ove
  8. Adder

    Help, please: Grs engraving vice

    I will take that with me
  9. Adder

    Help, please: Grs engraving vice

    My friend have taken a closer look on the vice. It`s probably the brass pin who cause thje problen. He could`nt get it out. Have told him to either call or use the e-mail adress I gor from you. Thanks for the help guys:-) Jørn-Ove
  10. Adder

    Help, please: Grs engraving vice

    Thanks for the tip Marty ! !(or at least I think it`s Marty:-))
  11. Adder

    Help, please: Grs engraving vice

    I suggested the same as you AllenC, and he said he will try to opening the screw. Hopefully everything turnes out okey.
  12. Adder

    Help, please: Grs engraving vice

    Thanks Sam. I will tell him to try again
  13. Adder

    Help, please: Grs engraving vice

    Hi from Norway. Have a question for you. I have a friend here in Norway who have problems with his Grs standard block vice. It will not turn smoothly. I gave him advice to send a request to Grs Company, he did, but he didnt get any response from them. Im certain that many of you experienced...
  14. Adder

    copper fish

    Papart1, I beleive that you are going to cut or making some dots on your copper fish, or have I wrong?. Did you use wire or sheet when inaying?
  15. Adder

    Texas Two Step

    Wonderful Sam!! Hope that you will post pictures when the entire gun is finnished. Jørn-Ove
  16. Adder

    Damar varnish alternative?

    I have also tried zapon lacquer with same result as dammar varnich. about 50% lacquer and 50% denatured alcohol. Think any shellack solution probably will give okey results.... The zapon lacquer solution is what I use today. Cant find any dammar varnish in the local stores where I live:-) Jørn-Ove
  17. Adder

    Nikon microscope ques

    I have an old Nikon SMZ-1 with some fungus/dirt problems, and a cheap 200$ newer microscope. The newer cheap microscope is far more clearer than the old one, so You maybe do better to buy an amscope instead, if you are on a low budget and can`t inspect the Nikon properly. I also have a new...
  18. Adder

    Engraving for the wall

    Nice! That will be nice on the wall with a proper frame, Im sure.
  19. Adder

    Latest knife learning inlay

    Thank you all for really nice feedback folks :thumbsup: :thumbsup: :thumbsup: Really aprreciate feedback from you. Of course negative ones too, but only if they aren`t too bad:D. I know I probably "bended some rules" how a scroll should look like, but designing a pattern is sadly a big issue...
  20. Adder

    Latest knife learning inlay

    Hi again friends. Here`s my latest knife project. I still got fantastic help while cutting the bolster from Masterengraver Roger Ronnie. Roger is a marvelous an patient teacher, no doubt about that. This time I have tried som gold inlay and some raised gold inlay on the flower in the middle...

Latest posts

Sponsors

Top